How much does it cost to install a grease trap?
Q: What will a grease trap cost my business? A: The average install for a small grease trap (0-100 gallons) is between $250 and $1500. The average cost for the installation of a new grease trap (750-1500) is between $4,000 and $8,500.
Do plumbers install grease traps?
Installations & Replacements for Grease Traps Our commercial plumbers can replace your grease trap or install one in your commercial kitchen to protect our plumbing. We’re experienced and helpful.
Can I install my own grease trap?
The most convenient place to install a grease trap is beneath your sink but it can also be installed outside your home. Unless your home has several sinks that are regularly used for cooking, setting it up beneath your sink is recommended.
How do you size a grease arrestor?
The peak flow rate from a kitchen/production area is known to be 0.5L/sec. The recommended grease arrestor size is calculated as follows: 0.5L/sec x 3600 sec/hour = 1800L/hour. Therefore the recommended size is 2000L (From Table 2).
Why are grease traps so expensive?
In order for grease traps to be effective, they must be properly sized, constructed and installed into your plumbing system. Because of these specific requirements, grease traps are traditionally more expensive than other plumbing operations.
How long does it take to install a grease trap?
The average installation time will vary. However, one can normally expect less than two hours from start to finish.
Where is a grease trap usually installed?
Hydromechanical grease interceptors (commonly called grease traps) are usually installed underneath the 3 compartment sink or in the floor of the kitchen. They trap grease over time and need to be pumped frequently, sometimes even weekly.
What size grease trap do I need?
The overall size of the trap is determined by the number of gallons of water flowing down your drains, which is your rate of incoming flow. You’ll also want to make sure your grease trap’s rated capacity is twice your flow rate. For instance, the rated capacity of a 20 gallon per minute (GPM) grease trap is 40 pounds.
Do residential homes have grease traps?
Grease traps are grease collection devices that are common in restaurant drainage systems, but they have a place in some large residential homes too. For houses with very busy kitchens and multiple kitchen sinks, a grease trap can be an effective asset to have, but they are not very common in a residential setting.
How big should my grease trap be?
They are different from conventional sinks since their capacity is clearly indicated. For machines with a 10-15 gallons capacity, use a grease trap that can handle at 15 pounds or higher. 20 to 30 gallons require a grease trap that can handle at least 20 pounds.
Who is responsible for grease trap?
14.56. 080 Single parcels. Property owners of commercial properties or their official designee(s) shall be responsible for the installation and maintenance of the grease interceptor serving multiple establishments that are located on a single parcel or for paying the FOG fee surcharge if there is no grease interceptor.
Where are grease interceptors required?
A grease interceptor or automatic grease removal device shall be required to receive the drainage from fixtures and equipment with grease-laden waste located in food preparation areas, such as in restaurants, hotel kitchens, hospitals, school kitchens, bars, factory cafeterias and clubs.
What is a grease arrestor?
Grease arrestors reduce the amount of greasy waste flowing into the wastewater system, by allowing fats, oil and grease to rise to the top and solids to sink to the bottom. Grease arrestors must be installed by licensed plumbers according to our trade waste requirements and the manufacturer’s instructions.
What do you need to know about grease traps in Adelaide?
Businesses with grease traps in Adelaide should know this for proper maintenance and compliance with the law. A grease interceptor or grease trap is a simple device used by foodservice businesses to prevent grease and oils and food waste from blocking up the waste piping system.
Are grease arrestors compliant with Australian standards 1657-2018?
All above ground grease arrestor installations are required to have a platform and steps manufactured to Australian Standards 1657-2018 for safe access to inspect and maintain the grease arrestor.
Can a dishwasher discharge to a grease arrestor?
Dishwashing machines and glass washers are not to discharge to grease arrestors. All industrial waste grease arrestors are to be vented to atmosphere, refer to venting of a grease arrestor diagram for details. Air admittance valves are not to be used on the grease arrestor vent or the sealed trade waste sampling point.