How do I troubleshoot my Bosch dishwasher?

How do I troubleshoot my Bosch dishwasher?

If your Bosch dishwasher’s Control Panel is front-facing try, with the door closed, pressing firmly then releasing the Start Button. Wait five seconds for the dishwasher to respond. If the dishwasher sounds like it has a motor/pump movement, then the dishwasher was likely just stuck in a paused cycle state.

How do I run diagnostics on my Bosch dishwasher?

To conduct a test cycle, hold down the “Power Scrub Plus” and “Regular Wash” button (or “Wash” and “Eco”). While these buttons are held down, press the “On/Off” button. The lights above the buttons will flash. Next, test the status of the individual dishwasher programs by pressing the button for each program.

Why does my Bosch dishwasher keep stopping and starting?

Door not closed properly The appliance will stop mid-cycle if the door is not closed properly. Ensure that the door is shut firmly and the latch engages fully. Check if the rear panel is being pressed in, for example by a hose holder, which has not been removed.

What does a blinking red light mean on a Bosch dishwasher?

As mentioned earlier, the main cause of red light blinking on a Bosch dishwasher is a door that is not appropriately closed. Put another way, your Bosch dishwasher blinks red as a way of telling you “Hey, please shut my door”. You can also consider resetting the appliance if shutting the door is not helpful.

Why won’t my Bosch dishwasher finish the cycle?

If your Bosch dishwasher is not completing a full cycle or stopping mid-cycle, it may be an issue with the door latch. Check for damage and replace the part if needed, and perform a system reset to have the cycle finish. If your unit won’t start, check that there is sufficient power and water.

How do you run a diagnostic cycle on a dishwasher?

Start this cycle by pressing the following buttons in this order: HEATED DRY, NORMAL WASH, HEATED DRY, NORMAL WASH. The buttons must be pushed within 5 seconds. After pushing these buttons, all the control lights will turn on and then the dishwasher will complete a short test cycle.

Why is my dishwasher turning off mid cycle?

The reason for the dishwasher to stop mid cycle is that the thermal fuse is shorting out because it is either fouled, dirty, broken, or loosely connected. If your dishwasher is older, the thermal fuse is used as a safety switch to stop the motor and circuit board when the dishwasher gets too hot.

Why is my dishwasher stuck on 1 minute?

This can be caused by a failed drain pump as well as a blockage in the outlet hose or something obstruction the drain pump.

How do I reset my Bosch dishwasher control board?

1) With the door closed and the dishwasher turned on, press and hold the Start button for 5 seconds. If your model has a display it should show “01” of “00”. Press the On/Off button (turning the dishwasher off) and the control should be reset.

How do I fix a blinking light in my dishwasher?

A blinking Start/Resume light signifies an interruption in the cycle or start-up. It can occur if you leave the door open during the cycle or due to a power interruption. To fix it, restart your unit and ensure you firmly close the door within no more than three seconds of pressing the Start/Resume button.

What to do if your Bosch dishwasher is not draining?

If your Bosch dishwasher is still not draining then you’ll need to continue downwards into the basin and towards the drain pump. After the filter is removed you’ll be faced with a drain mesh which simply lifts out. At this point you’re going to need to remove as much water as possible from the dishwasher to allow you to examine the drain pump.

How can I contact Bosch customer service for dishwasher repair?

How can I contact Bosch Customer Service for dishwasher repair? Please contact Bosch Customer Service at 1-800-944-2904 for troubleshooting assistance. Our US-based call center is open 24 hours a day, 7 days a week. You can also find a Bosch authorized servicer by clicking here.

Where is the reset button on a Bosch dishwasher?

On many modern Bosch dishwashers, the Reset button is the Start button, this can confuse some customers. To reset the modern Bosch dishwasher, press and hold the start button for about 3 to 5 seconds. On some older Bosch models, the reset feature may be called “cancel” or “drain”.

Why is my Bosch dishwasher leaking from the floor?

Normally, in these cases, you will observe Bosch Dishwasher leaking near the floor. The water lines that connect the dishwasher to the sink and drain are a natural place for leaks to occur. Inspect both ends of the water line that goes into the Bosch dishwasher and the one that comes out of the drain, looking for gaps or cracks.

Begin typing your search term above and press enter to search. Press ESC to cancel.

Back To Top