How do I access the Cisco 2950 switch?

How do I access the Cisco 2950 switch?

Click “Run” and then type “cmd” and press the “Enter” key. Type “telnet x.x.x.x” on the command line, replacing “x.x.x.x” with the IP address just configured on the Cisco Catalyst 2950. Press the “Enter” key. Type the telnet password just programmed into the Cisco Catalyst 2950 when requested.

How do I add a VLAN to EtherChannel?

Procedure

1. Log in to the primary Cisco Nexus series switch.
2. To run the configuration, type: Switch-A# config terminal.
3. To specify the port channel, type: Switch-A(config)# interface port-channel
4. To add the VLANs, type: Switch-A(config)# switchport trunk allowed vlan add VLAN_IDs.

How do you make EtherChannel?

EtherChannel Configuration

1. Up to eight ports can be configured, and all of these ports should be the same type (Fast Ethernet, Gigabit Ethernet, 10-Gigabit Ethernet).
2. Set all ports to function at the same Speed and Duplex settings.
3. Ensure that all ports are enabled and that none have been configured using the shutdown.

How can I find switch configuration?

How to configure Cisco switch?

1. Initial command prompt “Switch>” appears on the screen.
2. Type “enable” next to it and press “Enter”.
3. This will take you into the “EXEC” mode, also known as the Global Configuration mode.
4. Go into configure mode using configure terminal.
5. Enter the configuration commands one per line.

What is port channel in switch?

A port channel is a communication link between two switches supported by matching channel group interfaces on each switch. A port channel is also referred to as a Link Aggregation Group (LAG). Port channels combine the bandwidth of multiple Ethernet ports into a single logical link.

Can an EtherChannel be configured with STP?

Spanning tree protocol (STP) can be used with an EtherChannel. STP treats all the links as a single one and BPDUs are only sent down one of the links. This is where an EtherChannel is most desirable, it allows use of all available links between two devices. EtherChannels can be also configured as VLAN trunks.

What is EtherChannel in Cisco switch?

EtherChannel is a port link aggregation technology or port-channel architecture used primarily on Cisco switches. It allows grouping of several physical Ethernet links to create one logical Ethernet link for the purpose of providing fault-tolerance and high-speed links between switches, routers and servers.

What is the EtherChannel for catalyst 2950?

This document describes the set-up of an EtherChannel and 802.1Q trunking between Catalyst 2950 and Catalyst 2948G-L3 switches. EtherChannel can be called Fast EtherChannel (FEC) or Gigabit EtherChannel (GEC) depending upon the speed of the interfaces or ports used to form the EtherChannel.

Does the catalyst 2950 switch support Inter-Switch Link Protocol (ISL) trunking?

Note: The Catalyst 2950 switch supports only 802.1Q trunking, and does not support Inter-Switch Link Protocol (ISL) trunking. Catalyst 2948G-L3 and Catalyst 4908G-L3 switches share the same software image, so the Catalyst 2948G-L3 configuration used in this document also applies to the Catalyst 4908G-L3 switch.

What switches are used for Fast EtherChannel (FEC) trunking?

This document provides a sample configuration for Fast EtherChannel (FEC) and IEEE 802.1Q trunking between Cisco Catalyst Layer 2 (L2) fixed configuration switches and a Cisco router. The Catalyst L2 fixed configuration switches include the 2900/3500XL, 2940, 2950/2955, and 2970 switches.

How many etherchannels does a Catalyst 6500 switch support?

Catalyst 6500 switches that run Cisco IOS Software support L2 (switchport) and Layer 3 (L3) (routed port) EtherChannel configurations. A Catalyst 6500/6000 series switch supports a maximum of 64 EtherChannels (256 with Cisco IOS Software Release 12.1 (2)E and earlier).