What are the steps to configure a switch PDF?

What are the steps to configure a switch PDF?

1. Step 1: Cable a network.
2. Step 2: Clear the configuration on the switch.
3. Step 1: Enter privileged mode.
4. Step 2: Examine the current switch configuration.
5. Step 3: Display Cisco IOS information.
6. Step 4: Examine the Fast Ethernet interfaces.
7. Step 5: Examine VLAN information.
8. Step 6 Examine flash memory.

What are the steps to configure a switch?

1. Step 1: Inspect your hardware. Check the model number of your shiny new switch.
2. Step 2: Set up management IP.
3. Step 3: Check VTP revision number.
4. Step 4: Configure access ports.
5. Step 5: Configure trunk ports.
6. Step 6: Configure access ports.
7. Step 7: Set up VTY line config.

How do you initially configure a Cisco switch?

How to configure Cisco switch?

1. Initial command prompt “Switch>” appears on the screen.
2. Type “enable” next to it and press “Enter”.
3. This will take you into the “EXEC” mode, also known as the Global Configuration mode.
4. Go into configure mode using configure terminal.
5. Enter the configuration commands one per line.

Why do we configure switches?

Switch allows us to set IP address on interface level. IP address assigned on interface is used to manage that particular interface. To manage entire switch we have to assign IP address to VLAN1( Default VLAN of switch).

What two items must you configure on a switch in order to manage it from a remote network?

To prepare a switch for remote management access, the switch must be configured with an IP address and a subnet mask. Keep in mind that to manage the switch from a remote network, the switch must be configured with a default gateway. This is very similar to configuring the IP address information on host devices.

Which configuration is required in switch?

Basic switch configuration can be thought of as the minimum network, port, and security provisioning required for the production deployment of a switch. In practice, your exact needs will vary from environment to environment. And overall, effective switch management is a detailed topic in its own right.

What command is used to configure a Cisco switch?

Cisco Commands Cheat Sheet

Basic Configuration Commands
Command	Purpose
interface fastethernet/number	Enters interface configuration mode for the specified fast ethernet interface
reload	An exec mode command that reboots a Cisco switch or router
hostname name	Sets a host name to the current Cisco network device

What is initial switch configuration?

The following are the different steps we’ll accomplish in this video: Configure Hostname. Disable name resolution. Configure management IP address. Configure default gateway.

Do Cisco switches have IP addresses?

By default, Cisco switches forward Ethernet frames without any configuration. However, to perform switch management over the network or use protocols such as SNMP, the switch will need to have an IP address. The IP address is configured under a logical interface, known as the management domain or VLAN.

Why should you configure the Vty lines for the switch?

Configure the virtual terminal (vty) lines for the switch to allow Telnet access. If you do not configure a vty password, you will not be able to Telnet to the switch. Why is the login command required?

What you should know about configuring a Cisco IOS switch?

Initial Configuration. When the switch first comes up,it attempts to get an IP address by broadcasting a DHCP request on the network.

Incremental (Partial) Configuration. After the network is running,new services can be added by using the Cisco IOS agent.

Synchronized Configuration.

How do you restart a Cisco switch?

How To Reset Cisco ASR 1000 Router With Button : To reset your Cisco router to its factory default configuration using the Reset button: First switch on router. Then, Find the Reset button on the router (Generally back side of the router). Press and hold the Reset button with sensitive material while you power on the router.

What are the commands for Cisco switches?

Cisco Switch Configuration Commands. Configure terminal: This command is used to enter the global configuration mode of the Cisco switch. Hostname: This command assigns the Cisco switch’s hostname. Enable password: This command sets the enable password of the Cisco switch.

What is the default password for Cisco switches?

Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168.1.1 or 192.168.1.254. However, some differ as shown in the table below. Important: Remember to change the default login data once you’re in!